AiRTX Air Saver Nozzle & Hurricane Air Saver Nozzles

Save Compressed Air Use an Average of 70%!!

AiRTX^TM Air Saver Nozzles harness the power of compressed air to do BIG blow-off, cooling and parts ejection jobs, without spewing raw compressed air and noise all over your plant. It’s ideal for anything from a hand-held blow-off gun to multi-unit nozzle manifolds for conveyorized product or transfer lines. Even small air usage applications can show major cost reductions.– AiRTX Air International. – www.tjsolution.com

Air Saver Nozzle gives you cost and performance advantages with air amplification.It amplifies your compressed air flow 25 times, delivering high thrust with just a fraction of the compressed air wasted by open air lines.– www.tjsolution.com

One 1/4″ open air line, operating at 80 PSI on an eight-hour schedule, will waste high cost. The adjustable Air Saver Nozzle would use 70 percent less air – and provide 375 SCFM of air, compared to 36 SCFM from the open air line.

A system-wide changeover to Air Saver Nozzles can be like adding compressor capacity. Air Saver Nozzles will:

cut your energy bill
increase air flow with reduced noise level
reduce demand on your compressor
give you a return on investment in days.

AiRTX Air Saver Nozzles
Hurricane ¼ in. NPTF Air Saver Force Nozzle Aluminum or Stainless Steel Increased air flow – www.tjsolution.com Great for heavy duty applications Long reach with high thrust ¼” compressed air inlet	Hurricane ½ in. NPTF Air Saver Force Nozzle Aluminum or Stainless Steel High thrust at extended distances ½” fitting for large air flow – www.tjsolution.com Great at removing scaley or rusty parts, cleaning molds
¼ in. NPTF Air Saver Force Nozzle Aluminum or Stainless Steel Reduced noise level Strong thrust, low compressed air comsumption Move large amounts of scrap ¼” compressed air inlet	Hurricane ½ in. NPTM Aluminum Adjustable Air Saver Nozzle Aluminum Adjustable flow control ½” fitting for large air flow Extra large design for big blowoff performance
1/8 in. NPTM Aluminum Adjustable Air Saver Nozzle Aluminum or Stainless Steel – www.tjsolution.com Meets OSHA noise and dead end pressure requirements High volume of air with lowest possible air consumption Adjustable making it easy to adapt to existing application	1/8 in. NPTM Fixed Flow Air Saver Nozzle Brass or Stainless Steel Meets OSHA noise and dead-end pressure requirements 25:1 amplification increases flow without increased consumption Use for ejecting parts from molding machines, chip blow-off, plant air conservation
Hurricane High Thrust Wedge Jet – ¼ NPT Female Inlet Aluminum or Stainless Steel Highest thrust of any nozzle – www.tjsolution.com Meets OSHA noise & dead-end pressure requirements/li> No maintenance, no moving parts, no vibration Ejecting parts, blow-off of scrap, cooling extruded parts	High Thrust Wedge Jet – ¼ NPT Female Inlet Aluminum or Stainless Steel Highest thrust of any nozzle Meets OSHA noise & dead-end pressure requirements/li> No maintenance, no moving parts, no vibration Ejecting parts, blow-off of scrap, cooling extruded parts
1/8 in. NPTM Rubbertip Nozzle Rubber – www.tjsolution.com Meets OSHA noise and dead end pressure requirements	Barbed Brass Fixed Flow Air Saver Nozzle Brass – www.tjsolution.com Meets OSHA noise and dead-end pressure requirements 25:1 amplification increases flow without increased consumption Use for ejecting parts from molding machines, chip blow-off, plant air conservation
1/4 in. NPTM Aluminum Adjustable Flare Nozzle Aluminum Meets OSHA noise and dead end pressure requirements

AiRTX Air Saver Nozzles

Hurricane ¼ in. NPTF Air Saver Force Nozzle

Aluminum or Stainless Steel
Increased air flow – www.tjsolution.com
Great for heavy duty applications
Long reach with high thrust
¼” compressed air inlet

48005 Hurricane Fixed Force Nozzle - www.tjsolution.com

Hurricane ½ in. NPTF Air Saver Force Nozzle

Aluminum or Stainless Steel
High thrust at extended distances
½” fitting for large air flow – www.tjsolution.com
Great at removing scaley or rusty parts, cleaning molds

48107 Hurricane Fixed Force Nozzle - www.tjsolution.com

¼ in. NPTF Air Saver Force Nozzle

Aluminum or Stainless Steel
Reduced noise level
Strong thrust, low compressed air comsumption
Move large amounts of scrap
¼” compressed air inlet

48007 Fixed Force Air Saver Nozzle

Hurricane ½ in. NPTM Aluminum Adjustable Air Saver Nozzle

Aluminum
Adjustable flow control
½” fitting for large air flow
Extra large design for big blowoff performance

48109 Adjustable Force Nozzle- www.tjsolution.com

1/8 in. NPTM Aluminum Adjustable Air Saver Nozzle

Aluminum or Stainless Steel – www.tjsolution.com
Meets OSHA noise and dead end pressure requirements
High volume of air with lowest possible air consumption
Adjustable making it easy to adapt to existing application

1/8 in. NPTM Fixed Flow Air Saver Nozzle

Brass or Stainless Steel
Meets OSHA noise and dead-end pressure requirements
25:1 amplification increases flow without increased consumption
Use for ejecting parts from molding machines, chip blow-off, plant air conservation

40008/48008 Adjustable Force Nozzle - www.tjsolution.com

Hurricane High Thrust Wedge Jet – ¼ NPT Female Inlet

Aluminum or Stainless Steel
Highest thrust of any nozzle – www.tjsolution.com
Meets OSHA noise & dead-end pressure requirements/li>
No maintenance, no moving parts, no vibration
Ejecting parts, blow-off of scrap, cooling extruded parts

High Thrust Wedge Jet – ¼ NPT Female Inlet

Aluminum or Stainless Steel
Highest thrust of any nozzle
Meets OSHA noise & dead-end pressure requirements/li>
No maintenance, no moving parts, no vibration
Ejecting parts, blow-off of scrap, cooling extruded parts

High Thrust Wedge Jet- www.tjsolution.com

1/8 in. NPTM Rubbertip Nozzle

Rubber – www.tjsolution.com
Meets OSHA noise and dead end pressure requirements

Barbed Brass Fixed Flow Air Saver Nozzle

Brass – www.tjsolution.com
Meets OSHA noise and dead-end pressure requirements
25:1 amplification increases flow without increased consumption
Use for ejecting parts from molding machines, chip blow-off, plant air conservation

1/4 in. NPTM Aluminum Adjustable Flare Nozzle

Aluminum
Meets OSHA noise and dead end pressure requirements

AiRTX International Nozzles & Your Method Comparison Chart

Conventional Air Movers – Consumption and Costs
Method	Size	Air Consumption				Cost per 1000 Cu.Ft. @ 100 psi
Method	Size	80 psi	LPM	100 psi	LPM	Per Day	Per Year
Pipe Nipple	3/8″ x 2′	290	8207	350	9905	$41.60	$10,858
Copper Tube	1/4″ x 1′	36	1019	42	1189	$5.04	$1,310
Copper Tube	1/2″ x 1′	19	5377	240	6792	$28.80	$7,488
Hole in Pipe	1/8″	18	509	22	623	$2.64	$686
Hole in Pipe	1/4″	70	198	86	2434	$10.80	$2,228

Cost is based on $0.25 per 1000 cu.ft. of air per hour and duty cycle of 8 hours per day, 260 days per year.

Compressed Air Cost

1 – 100 Hp compressor cost approximately $35,000 per year to operate.– www.tjsolution.com

Power Cost =	Hp x 0.746 x hour x rate	= $34,800
	motor efficiency

Power Cost =	Hp x 0.746 x 6,000 x 7 cents/kw	= $34,800
	90%

How does the Air Saver Nozzle work?

The Air Saver releases a tiny amount of compressed air at near-sonic velocity through a fine, ring-shaped nozzle. As the high-speed “tube” of air emerges from the nozzle, it creates a strong vacuum along its sides, pulling a much larger volume of surrounding air into the stream. At 12″ in front of the nozzle, the airstream is 3-1/2″ diameter and capable of producing force levels of 3.4 to 20.1 ozs. (0.096 – 0.570 kg) depending on the setting. – www.tjsolution.com

Applications:-

Ejecting parts from molding machines and stamping presses
Blow off chips, trim scrap, swarf
Part cleaning before painting
Plant air conservation and noise reduction
Cooling molded or cast parts
Cleaning/cooling of metal strip and plastic/paper webs
Cleaning/cooling of conveyorized or transfer line parts

Stainless steel or aluminum construction

Low-cost aluminum Air Savers are ideal for most industrial applications. Stainless steel units are ideal for:

food processing applications
hot corrosive environments
maximum durability in harsh environments

Always consider our Aluminum Extension rods or our Flexible Sta-Put hoses for those hard to reach or hard to mount locations. The rods and hoses can be added to your order in the shopping cart with each item.

Plastics – Molding

The Stainless Steel 1/8 in. NPTM Adjustable Air Saver Nozzle Model 48009 uses a minimal amount of compressed air to produce high volume and calling for quick parts release. Small size and instant on/off make it ideal for molding machines.

Woodworking – Drilling Chip Removal

Drilling Chip Removal - www.tjsolution.com

The 25:1 air amplification of the Stainless Steel 1/8 in. NPTM Adjustable Air Saver Nozzle Model 48009 provides plenty of cleaning power for a factory air gun, while still meeting OSHA requirements for dead-end pressure and noise limits.