Laser Diameter Display Unit Takikawa -Specification

Model	LDM-110	LDM-110EX	LDM-1000	LDM-1000EX	LDM-210	LDM-210C
No. of Axes	For Single	Max. 2	Max. 5	Max. 3	For Single
Scanning cycle	400 times/sec	400 times/sec	400 times/sec	400 times/sec	2000 times/sec
No. of Averaging time	1-2048 (16 steps)	1-2048 (8 steps)	1-2048(22 steps) at LDM-1000LS 1-1024(19 steps) at LDM-1000XY		1-2048 (12 steps)
Measuring mode	16 kinds	8 kinds (X,Y axis each)	16 kinds + Optional edges measurement per each axis		Optional edges measurement per each axis
Processing function	NG	Average, Difference, Large dia. measurement, etc.			NG
Cable cover(Wall) thickness processing	NG	NG	OK(by LDM-1000XY)		NG
Display device	7 segment LED		Graphic LCD	7 segment LED	7 segment LED
No. of Display digit	4-5 digits	4-5 digits	3-6 digits	3-6 digits	4-5 digits
Processing contents monitor	NG	NG	OK	OK	NG
Center position monitor	LED(8pcs)	LED(8pcs) (X,Y axis each)	Graphic bargraph per each axis	LED(8pcs) per each axis	LED(8pcs)	LED(15pcs)
No. of channel of Recorder output	1	1	1 channel per board (LDM-1000LS/XY)		1
Recorder output performance	Max.+/-10V, Resolution 12bits(=approx.10mV/1bit), Output impedance 100ohm(approx.), Deviation/Absolute value switch over available
Recorder output gain	1μm-1m/V(decade steps)		0.1μm～1m/V(decade steps)		1μm-1m/V(decade steps)
Digital dia. controller connection	OK	OK	NG	NG	OK	NG (Built-in Dia.Controller)
Center value setting	5 digits	5 digits	6 digits	6 digits	5 digits
High/Lo limit tolerance setting	4 digits	4 digits	6 digits	5 digits	5 digits
High/Low limit contact output	1a contact(*2)		1a contact(*2) per board(LDM-1000LS/XY)		1a contact(*2)
High/Low limit contact output	Contact rating: AC250V 2A(Resistance load)
Error contact output	1b contact (Close when power OFF)		1b contact(Close when power OFF) (Combined use by each board)		1b contact (Close when power OFF)
Error contact output	Contact rating: AC250V 2A(Resistance load)
Laser remote terminal	OK	OK (X,Y common)	OK(each LDM-1000LS board)		OK
Hold terminal	OK	OK (X,Y,P common)	OK(each LDM-1000LS/XY board)		OK
Edge monitoring function	OK	OK	OK	OK	OK
Self-diagnosis mode	OK	OK	OK	OK	OK
Multi-point calibration function	OK	NG	NG	NG	OK
Trigger function (Max. meas., Deviation meas., etc.)	NG	NG	OK	OK	NG
Offset function	NG	NG	OK	OK	NG
Zero set function	OK	NG	OK	OK	OK
mm/inch changeover function	NG	NG	OK	OK	NG
Programing function	NG	NG	OK(30 kinds)	OK(9 kinds)	NG
Graph display	NG	NG	OK	NG	NG
Serial port	OK	OK	OK	OK	OK	OK
BCD output	Option		OK(by LDM-1000BCD)		Option
Cable length	Standard 5 meters, Max. 30 meters (Extensible to 120m.max. as option)
Power supply	AC100-240V Free power supply 50/60Hz
Power consumption	less than 11VA	less than 14VA	less than 15VA(only display unit) less than 8VA(each board)		less than 15VA	less than 20VA
Ambient condition	Temperature:0-45 degree centigrade, Humidity:35～85%RH(no condensation)
Outside dimension	144(W) * 72(H) * 191(D)[mm]		216(W) * 144(H) * 225(D)[mm]		144(W) * 72(H) * 191(D)[mm]	144(W) * 72(H) * 241(D)[mm]
Weight	Approx. 1.5kg	Approx. 1.6kg	Approx. 4kg (only display unit) Approx. 280g (each board)		Approx. 1.5kg	Approx. 1.8kg

Takikawa also have Cable Extention Adaptor (LDM-201,-202), to be used in case distance between a Laser diameter Scanning Unit and a Display Unit exceeds 30 meters.
Dividing Adaptor (LDM-205,-206), which divides output signals from Scanning Unit.
Laser Diameter LDM-210/LDM-210C uses the detection part of the exclusive use because the scan time is different from the conventional model.

[UP]

Home

Products

Applications

Service

About us

Laser Diameter Display Unit Takikawa -Specification

Model

LDM-110

LDM-110EX

LDM-1000

LDM-1000EX

LDM-210

LDM-210C

Takikawa > Laser micrometer > Laser Diameter head > Display unit 's Takikawa