AiRTXTM Air Saver Nozzles harness the power of compressed air to do BIG blow-off, cooling and parts ejection jobs, without spewing raw compressed air and noise all over your plant. It's ideal for anything from a hand-held blow-off gun to multi-unit nozzle manifolds for conveyorized product or transfer lines. Even small air usage applications can show major cost reductions.- AiRTX Air International. - www.tjsolution.com
Air Saver Nozzle gives you cost and performance advantages with air amplification.It amplifies your compressed air flow 25 times, delivering high thrust with just a fraction of the compressed air wasted by open air lines.- www.tjsolution.com
One 1/4" open air line, operating at 80 PSI on an eight-hour schedule, will waste high cost. The adjustable Air Saver Nozzle would use 70 percent less air - and provide 375 SCFM of air, compared to 36 SCFM from the open air line.
A system-wide changeover to Air Saver Nozzles can be like adding compressor capacity. Air Saver Nozzles will:
cut your energy bill
increase air flow with reduced noise level
reduce demand on your compressor
give you a return on investment in days.
AiRTX Air Saver Nozzles |
|
|---|---|
Hurricane ¼ in. NPTF Air Saver Force Nozzle
 |
Hurricane ½ in. NPTF Air Saver Force Nozzle
 |
¼ in. NPTF Air Saver Force Nozzle
|
Hurricane ½ in. NPTM Aluminum Adjustable Air Saver Nozzle
 |
1/8 in. NPTM Aluminum Adjustable Air Saver Nozzle
 |
1/8 in. NPTM Fixed Flow Air Saver Nozzle
 |
Hurricane High Thrust Wedge Jet - ¼ NPT Female Inlet
 |
High Thrust Wedge Jet - ¼ NPT Female Inlet
|
1/8 in. NPTM Rubbertip Nozzle
 |
Barbed Brass Fixed Flow Air Saver Nozzle
 |
1/4 in. NPTM Aluminum Adjustable Flare Nozzle
 |
|
Conventional Air Movers - Consumption and Costs |
|||||||
|---|---|---|---|---|---|---|---|
Method |
Size |
Air Consumption |
Cost per 1000 Cu.Ft. @ 100 psi |
||||
80 psi |
LPM |
100 psi |
LPM |
Per Day |
Per Year |
||
Pipe Nipple |
3/8" x 2' |
290 |
8207 |
350 |
9905 |
$41.60 |
$10,858 |
Copper Tube |
1/4" x 1' |
36 |
1019 |
42 |
1189 |
$5.04 |
$1,310 |
Copper Tube |
1/2" x 1' |
19 |
5377 |
240 |
6792 |
$28.80 |
$7,488 |
Hole in Pipe |
1/8" |
18 |
509 |
22 |
623 |
$2.64 |
$686 |
Hole in Pipe |
1/4" |
70 |
198 |
86 |
2434 |
$10.80 |
$2,228 |
Cost is based on $0.25 per 1000 cu.ft. of air per hour and duty cycle of 8 hours per day, 260 days per year.
Compressed Air Cost1 - 100 Hp compressor cost approximately $35,000 per year to operate.- www.tjsolution.com
OR
|
The Air Saver releases a tiny amount of compressed air at near-sonic velocity through a fine, ring-shaped nozzle. As the high-speed "tube" of air emerges from the nozzle, it creates a strong vacuum along its sides, pulling a much larger volume of surrounding air into the stream. At 12" in front of the nozzle, the airstream is 3-1/2" diameter and capable of producing force levels of 3.4 to 20.1 ozs. (0.096 - 0.570 kg) depending on the setting. - www.tjsolution.com
Ejecting parts from molding machines and stamping presses
Blow off chips, trim scrap, swarf
Part cleaning before painting
Plant air conservation and noise reduction
Cooling molded or cast parts
Cleaning/cooling of metal strip and plastic/paper webs
Cleaning/cooling of conveyorized or transfer line parts
Low-cost aluminum Air Savers are ideal for most industrial applications. Stainless steel units are ideal for:
food processing applications
hot corrosive environments
maximum durability in harsh environments
Always consider our Aluminum Extension rods or our Flexible Sta-Put hoses for those hard to reach or hard to mount locations. The rods and hoses can be added to your order in the shopping cart with each item.
Plastics - Molding
The Stainless Steel 1/8 in. NPTM Adjustable Air Saver Nozzle Model 48009 uses a minimal amount of compressed air to produce high volume and calling for quick parts release. Small size and instant on/off make it ideal for molding machines. |
Woodworking - Drilling Chip Removal
The 25:1 air amplification of the Stainless Steel 1/8 in. NPTM Adjustable Air Saver Nozzle Model 48009 provides plenty of cleaning power for a factory air gun, while still meeting OSHA requirements for dead-end pressure and noise limits. |
The models below are all very special price for you, please inquiry to us. You will get a special price along with our special gift to you.
|
|
|
///////////////////////////////////////////////////////////////////////////<TOP>
______________________________COPYRIGHT 2009 T.J.SOLUTION CO.,LTD.
 |
|---|
AiRTX - Air Saver Nozzles |
 |
